溅射MOS_2膜和PTFE膜在边界润滑条件下的摩擦学性能之研究

本文对溅射二硫化钼(MoS_2)膜和聚四氟乙烯(PTFE)膜在边界润滑条件下的摩擦学性能进行了研究。结果表明,与未镀膜的轴承钢相比,这两种固体润滑膜都具有较好的抗粘着性和减摩性,以及对硬质颗粒良好的嵌入性,但在同样的负荷条件下,PTFE膜的磨损比MoS_2膜的轻微。     

硫含量对GCr15轴承钢摩擦学性能影响的试验研究

冶炼了3炉不同硫含量的GCr15轴承钢,采用MM-200、MPX-200和Falex摩擦磨损试验机对其进行了不同条件下的摩擦磨损试验,研究了硫含量对GCr15轴承钢摩擦学性能的影响规律。结果表明,随着硫含量的增加,GCr15轴承钢的摩擦系数降低,耐磨性能和抗咬合性能提高。作者根据金相分析、电子探针线扫描和电解分离法的测试结果指出,硫在GCr15轴承钢中主要是以化合态的形式存在,并对其作用机理进行了初步探讨。     

中柱失效工况下单层组合框架受力理论分析

基于已有试验，本文提出了轴向弹簧和转动弹簧约束的组合框架简化计算模型，推导了在集中荷载作用下刚性、半刚性连接平面组合梁双跨钢框架移除中柱后的荷载-跨中挠度曲线计算公式，考虑了压拱效应和连接刚度的影响，将公式计算结果与试验结果进行对比证明了推导过程和计算公式的可靠性．在对比结果的基础上，根据已有试验和模拟结果对已有悬索阶段的计算公式进行修正，修正后的公式与试验结果吻合较好．     

New exact results for the effective electric, elastic, piezoelectric and other properties of composite ellipsoid assemblages

In this paper we present a unified treatment of composite ellipsoid assemblages in the setting of uncoupled phenomena like conductivity and elasticity and coupled phenomena like thermoelectricity and piezomagnetoelectricity. The building block of this microgeometry is a confocal ellipsoidal particle consisting of a (possibly void) core and a coating. All space is filled up with such units which have different sizes but possess the same aspect ratios. The confocal ellipsoids may have the same orientation in space or may be randomly oriented. The resulting microgeometry simulates two-phase composites in which the reinforcing components are short fibers or elongated particles. Our main interest is in obtaining information of an exact nature on the effective moduli of this microgeometry whose effective tensor symmetry structure depends on the packing mode of the coated ellipsoids. This information will sometimes be complete like the full effective thermoelectric tensor of an assemblage which contains aligned ellipsoids in which the coating is isotropic and the core is arbitrarily anisotropic. In the majority of the cases however the maximum achievable exact information will be only partial and will appear in the form of certain exact relations between the effective moduli of the microgeometry. These exact relations are obtained from exact solutions for the fields in the microstructure for a certain set of loading conditions. In all the considered cases an isotropic coating can be combined with a fully arbitrary core. This covers the most important physical case of anisotropic fibers in an isotropic matrix. Allowing anisotropy in the coating requires the fulfillment of certain constraint conditions between its moduli. Even though in this case the presence of such constraint conditions may render the anisotropic coating material hypothetical, the value of the derived solutions remains since they still provide benchmark comparisons for approximate and numerical treatments. The remarkable feature of the general analysis which covers all treated uncoupled and coupled phenomena is that it is developed solely on the basis of potential solutions of the conduction problem in the same microgeometry.     

预应力钢梁体外索的张力增量分析

将预应力钢梁看作梁与索的组合结构,充分考虑了二者之间的相互作用．利用变分原理推导出在外荷载作用下,体外索张力增量的计算公式,并通过预应力钢梁模型试验对计算结果进行了验证．     

常速度拉伸实验惯性效应的实验研究

本文统计了１５０根Ａ３低碳钢比例拉伸试件的断口位置，并测定了常速度拉伸（４００ｍｍ／ｍｉｎ，０．５ｍｍ／ｍｉｎ）时应变随时间和沿杆长的分布以及应力应变关系；发现７２％试件的断口靠近不动端内。同一时刻在设定速度为４００ｍｍ／ｍｉｎ时杆中最大工程应变差１８％．     

弹／粘塑性柱体扭转问题的函数Laplace变换解

在应力Ｌａｐｌａｃｅ变换分析粘塑性轴对称问题基础上，对弹性－弹／粘塑性圆柱体扭转全过程进行分析，根据柱体扭转的应力分布，构造应力函数与位移函数，并对函数进行Ｌａｐｌａｃｅ变换。相应求出圆柱体、空心圆柱体的Ｌａｐｌａｃｅ变换解，以及圆柱体的弹性－粘塑性交界线值     

不同水介质润滑下GCr15钢的微动磨损特性

采用液压高精度材料试验机考察了平面-球面接触GCr15钢摩擦副在海水、酸性水和洁净水等3种不同水介质润滑下的微动磨损性能．用激光扫描显微镜(LSM)观察了磨痕表面形貌．结果表明：3种水介质对钢-钢摩擦副具有明显的润滑作用，其中酸性水的润滑作用最明显；磨损体积损失同介质的润滑作用和腐蚀作用相关，在洁净水和海水介质润滑下的磨损体积损失较小，在酸性水介质润滑下的磨损体积损失较大；在海水润滑下的GCr15钢磨损表面呈现明显的点蚀特征．     

超静定型钢桁架优化设计的面积比法

满应力准则是对超静定型钢桁架进行优化设计的有效方法．但这种方法的主要缺点在于收敛速度很慢甚至不收敛,这给设计工作带来很大的不便．对问题进行了研究,在“型钢压杆稳定设计直接法”的基础上,提出了满应力优化设计的一种新方法——面积比法,有效地提高了设计过程的收敛速度,降低了设计成本,供有关结构设计人员参考．     

高速公路工程中水泥搅拌桩桩身合理设计强度研究

在公路工程的搅拌桩地基设计中,一般假设加固区桩土变形协调,从而采用复合地基理论进行设计。但是目前许多的工程实践表明在路堤荷载作用下,搅拌桩地基桩土之间存在差异沉降,桩身强度不能够完全发挥,为此需要对复合模量的表达式进行改进。本文采用有限元分析了路堤荷载作用下搅拌桩地基的变形响应情况,分析了加固区桩间土变形与桩身模量之间关系,得到了水泥土搅拌桩强度的合理范围。